9.00 -17.00 
Ubiquiti EV Station Lite - 22 kW three-phase EV charging station (UC-EV-Station-Lite)
The Ubiquiti EV Station Lite is a three-phase charging station (22 kW, 400V AC, 32A) equipped with an integrated, 7-meter cable with a Type 2 connector. It features a 1 GbE RJ45 port, WiFi 6 and Bluetooth 5.0 modules, and an IP55 enclosure. It supports standalone mode or management via the UniFi Connect system, offering a built-in 1.7" screen and a full set of electrical protections (OVP, UVP, OCP).
Ubiquiti EV Station Lite – Three-Phase 22 kW Electric Vehicle Charging Station
Ubiquiti EV Station Lite (UC-EV-Station-Lite) is a three-phase electric vehicle charging station with a maximum power output of 22 kW (400V AC, 32A). The device is compatible with vehicles equipped with a Type 2 charging connector (IEC 62196-2). The station features an integrated 7-meter charging cable. The device can operate fully autonomously or be integrated with the UniFi Site Manager system, allowing for more detailed configuration, statistics monitoring, and limiting maximum output current.
Management is powered by a dual-core Arm Cortex-A53 processor clocked at 1 GHz. Network communication is handled via a Gigabit Ethernet port (1 GbE RJ45) and wireless modules: Wi-Fi with 802.11ax standard support and Bluetooth 5.0. Additionally, a single USB-C port is located on the enclosure. The charging station includes various safety protections, including over-voltage protection (OVP), under-voltage protection (UVP), over-current protection (OCP), and a leakage current detection system. Status information (ready, charging in progress, error) is displayed on a built-in 1.7-inch screen using corresponding colors (blue, green, red). Charging automatically stops once the vehicle's battery is fully charged.
The enclosure is made of polycarbonate, providing IP55-rated water and dust resistance. The dimensions of the unit are 254.7 x 192.7 x 101.4 mm, and it weighs 7.2 kg. The design allows for installation directly on a wall or on a dedicated mounting stand. Management requires the use of UniFi Connect software, and NFC card registration requires the simultaneous operation of the UniFi Access application on the same hardware console.
Note: Safe operation of the equipment requires the use of a dedicated circuit breaker and a residual current device (30 mA RCD) in the electrical distribution board.
Key Features
-
Power and Supply: Three-phase charging 400V AC, 32A, maximum power up to 22 kW.
-
Charging Connector: Type 2 plug (IEC 62196-2) on an integrated 7 m cable.
-
Compatibility: Full support for battery electric vehicles (BEV) and plug-in hybrid electric vehicles (PHEV).
-
Connectivity Interfaces: 1x 1 GbE RJ45 port, 1x USB-C port, Wi-Fi (802.11a/b/g/n/ac/ax), Bluetooth 5.0.
-
Management System: Standalone mode or full integration with UniFi Site Manager; 1.7" status display.
-
Electrical Protection: Built-in OVP, UVP, OCP, and leakage current detection system.
Technical Specifications
| Power Input | 400V AC, ~32A, 50/60 Hz, 3-phase (3φ) |
| Power Output | 400V AC, ~32A, 50/60 Hz, 3-phase (3φ) |
| Charging Cable Length | 7 m (23 ft) |
| Charging Connector | IEC 62196-2 Type 2 |
| Circuit Parameters (Max. Load) | 40A/32A, 40A/25A, 30A/20A, 20A/16A, 15A/10A, 10A/8A |
| Plug-in Connection | 40A: No 32A, 25A, 20A, 16A, 10A: Yes |
| Hardwired Connection | 40A, 32A, 25A, 20A, 16A, 10A: Yes |
| Display | 1.7" Status display |
| Processor | Dual-core Arm® Cortex®-A53, 1 GHz |
| Connectivity | (1) GbE RJ45 port, (1) USB-C port, Bluetooth® 5.0, Wi-Fi |
| Wi-Fi Standards | 802.11a/b/g/n/ac/ax |
Management |
|
| Management Application | UniFi Connect: Version 3.21 or later UniFi Connect iOS™ and Android™: Version 2.32 or later |
Other |
|
| Dimensions | 254.7 x 192.7 x 101.4 mm (10 x 7.6 x 4") |
| Weight | 7.2 kg (15.9 lb) |
| Housing Material | Polycarbonate |
| Mounting | Wall or pedestal mount |
| Weatherproofing | IP55 |
| Ambient Operating Temperature | -30 to 50° C (-22 to 122° F) |
| Ambient Operating Humidity | 5 to 90% (non-condensing) |
| IEC 61851-1 Compliant | Yes |
| Certifications | CE |
Ubiquiti EV Station Lite – Frequently Asked Questions (FAQ)
EV Station Lite is compatible with all battery electric vehicles (BEVs) and plug-in hybrid vehicles (PHEVs) that support standard AC Level 2 charging via the following connector:
- Type 2 (IEC 62196-2)
The use of third-party adapters is not recommended and may affect charging performance, safety, and warranty terms.
EV Station Lite can operate independently as a standard AC Level 2 charger. It can also be integrated with UniFi Site Manager for advanced configuration, monitoring, and centralized management.
EV Station Lite is an AC Level 2 charger that delivers:
- Up to 3-phase charging at 32 A (approximately 22 kW)
Actual charging speed may vary depending on vehicle capabilities and electrical service installation parameters.
EV Station Lite is equipped with the following internal protection mechanisms:
- Overvoltage Protection (OVP)
- Undervoltage Protection (UVP)
- Overcurrent Protection (OCP)
- Residual Current / Leakage Detection
Depending on local building and electrical codes, the following external protection devices are required or recommended:
- Dedicated miniature circuit breaker (MCB)
- Residual Current Device (RCD) with 30 mA sensitivity
Yes. EV Station Lite is certified in accordance with relevant regional safety standards, including UL, CE, and IEC (depending on model variant and deployment region).
The branch circuit must be sized based on maximum charging current requirements. For example, a 32 A charger typically requires a circuit protected by at least a 40 A breaker (in accordance with standard 125% continuous load rating rules).
Yes. A dedicated circuit breaker is required to connect EV Station Lite. Sharing the branch circuit with other electrical appliances is not recommended, as it compromises safety and charging stability.
Yes. Proper connection of the protective earth (PE) conductor is essential during EV Station Lite installation to ensure user safety and protect against electric shock, equipment damage, and short circuits.
Yes. We strongly recommend having EV Station Lite installed by a licensed electrician to ensure maximum safety and full compliance with local electrical standards and building regulations.
Yes, maximum output current limits can be easily configured within UniFi Site Manager software.
Yes, charging stops automatically once the vehicle reaches a full charge or meets predefined charge limits.
Potential reasons include:
- On-Board Charger (OBC) limitations: The vehicle's internal AC charger may have a lower maximum rating than the station's capacity.
- Battery protection algorithms: As state-of-charge approaches full capacity (typically 80–90%), the vehicle Battery Management System (BMS) automatically ramps down current.
- Thermal derating: High ambient temperatures or direct sunlight may trigger temporary power throttling on the station or vehicle to prevent overheating.
- System settings: Maximum charging current may have been manually reduced in configuration settings.
Yes, the device supports Wi-Fi and Ethernet connectivity (depending on model variant), enabling seamless integration into existing UniFi network deployments.
Yes, standard charging operations remain fully functional offline. Only remote monitoring and centralized cloud management features will be temporarily unavailable until connectivity is restored.
The status LED on EV Station Lite indicates operational status as follows:
- Blue: Standby mode / Ready to charge
- Green: Charging in progress
- Red: Error state or fault detected
Error codes and diagnostic alerts can be checked directly on the device panel or within the UniFi Site Manager application for rapid troubleshooting.
| Manufacturer SKU | UC-EV-Station-Lite |
|---|---|
| Manufacturer | Ubiquiti |
| GPSR contact | Ubiquiti International Holding B.V. Ekkersrijt 3102, 5692 CC Son en Breugel support@ui.com |
Please complete your information below to login.
Sign In
Create New Account